2000 Grand Banks 52 Europa

About this boat

This 2000 Grand Banks 52 Europa is listed at 54.08 ft in overall length and 15.42 ft in beam. Step aboard this stunning 2000 Grand Banks 52 Europa, a timeless trawler that blends legendary Grand Banks craftsmanship with extensive upgrades and meticulous care. This is a must-see yacht for the discerning buyer seeking comfort, reliability, and classic style. See Below for Detailed info on upgrades over the years. Highlights & Upgrades: The Europa layout provides an ideal balance of indoor and outdoor living, featuring a spacious salon, excellent visibility from the helm, and generous accommodations for extended cruising or liveaboard comfort. This yacht has been professionally maintained with no expense spared, reflecting an owner who truly understands and appreciates the Grand Banks legacy. From her mechanical systems to her cosmetic finishes, she stands out as a premium example of this iconic model. A beautiful, well-cared-for classic trawler—ready for her next adventure. Walkthrough The large covered aft deck is a spacious area and very comfortable for several deck chairs and room for a table. At the transom there is a Freedom hydraulic dinghy lift so its just a push of a button to launch and retrieve a tender. She also is equipped with a Marquipt 800-lb. davit located to aft on the flybridge. A staircase from the aft deck to the flybridge leads to an expansive area with new Sunbrella Bimini top on a double stainless steel frame. Forward on the bridge there is an expansive L-settee to starboard with a beautiful GB teak table. Her helm is center with a new Stidd helmseat and additional seating is to port. All flybridge cushions and covers are new March 2021 and a new stainless steel propane grill was installed in 2021. Entering the salon from the large covered aft deck either through the wide sliding aft deck doors or via forward port and starboard pilothouse doors at the helm. The bright and open salon boasts teak parquet floors and a richly-upholstered L-settee new March 2021 with teak yacht table with built in cup holders to starboard. To port is a straight settee. All seating features storage beneath and the interior has received new upholstery in Dec 2020. A custom corner entertainment system cabinet is at the aft bulkhead. Moving forward, her large well-equipped U-shaped galley is to starboard opposite the port dinette area. The galley offers an abundance of storage with features such as overhead lockers that drop down for plate and glass storage as well as in counter storage. In the past year the galley has seen a custom refit with new stainless steel upright refrigerator and freezer, new stainless steel ice maker and custom stainless steel stove and oven with overhead vent. When the new appliances were being installed a custom marine carpenter added a spice rack drawer, pots and pans drawer and beautifully done silverware and cutlery drawer. The lower helm features a full suite of electronics (repeated on the flybridge) including a new Garmin radar and KVH SAT TV in 2021, large integrated chart locker, new Stidd helmseat and comfortable double guest seating to port and starboard with footrest. To port of this helm station is a companionway to access the three Staterooms below. Down the companionway to port of the lower helm is access to the Staterooms and Heads. Below is the landing and aft is the private and voluminous full-beam Master Stateroom with queen island berth bordered by night tables with reading lights. There is a straight settee to starboard and built-in vanity and storage drawers to port. Large hanging lockers are positioned on both port and starboard. The en suite Master Head has a VacuFlush toilet and sink to starboard and a separate stall shower room to port allowing for simultaneous use of these areas while maintaining privacy. The VIP Guest Stateroom forward features a V-berth with filler/insert so it can be one huge berth or separated easily into two singles. There are built-in drawers, night tables and reading lights. There is plenty of storage throughout with integrated cabinets, drawers and a custom cedar-lined hanging closet. Natural lighting is provided through portholes with an overhead hatch. Shades are installed on all portholes and hatch. The second Guest Stateroom with athwartship oversized double berth to starboard also has a cedar-lined hanging locker and additional storage. The shared Guest Head is to port with stall shower. Open the large hatch on her aft deck and you have a perfect storage space. On the port side are the full-size separate washer and dryer units. Moving forward is her engine room access. Once through the entry door, you have full stand-up headroom. Everything in this area is easy to get to and in impeccably nice condition. There is an extensive spare parts kit onboard with almost anything anyone would want to have onboard for long-term cruising. Crosswinds is an incredibly well cared for Grand Banks 52 Europa. The boat has been highly updated and carefully serviced to keep her in pristine condition in every way.Exterior EquipmentAir horn Anchor, Port Galvanized Bruce SL/Claw 66-lb. with 200' 3/8"S/S chain Anchor, Stbd Galvanized CQR Plow 75-lb. with 100' 3/8" S/S chain and 100' 5/8 nylon 3-strand rode Anchor chain locker, divided for rope & chain Anchor platform, fiberglass, with pulpit Anchor windlass locker, fiberglass Ball valves on thru hull above waterline, bronze Bow pulpit with dual anchor rollers Canvas Covers, Sunbrella - Flybridge helm, seating and windlass Chocks and cleats, stainless steel Courtesy lights, side decks Deck fillers, diesel fuel and water, S/S Engine room vents Flagstaff holders, bow and stern Fresh water outlet, fwd Grab rails, stainless steel Inspection deck plate for fuel tanks, port & stbd Navigation light boards, Teak Mast, hinged, FRP ? supports radar & bracket, anchor/steaming lights, windex array, SAT TV receiver dome & remote GPS antenna Rail gates at port and starboard Safety rails on main deck, stainless steel Stanchions, stainless steel Step plates at rail gate openings Vents for fuel and water tanks Waste pump-out deck fittings, stainless steel Lofrans Falkon Windlass, horizontal, rope/chain, three-station, 12V/1500W Aft DeckStaircase to flybridge, molded fiberglass w/louvered door for storage inside Rail gate Safety rails, Teak or stainless steel Sliding hatch to F/B with Teak frame Swim platform, extended, Teak Swim ladder Transom, Teak Transom door Transom shower with retractable hose hot/cold Compass Deck - main in Teak, side and rear in non-skid Electronics locker Chart Locker Helmseat High Water Alarms, Rule Instrumentation raised dashboard, fiberglass Outlet, 12V DC Rail around flybridge windshield, stainless steel Safety rails, stainless steel Seats with cushions, port & stbd Settee-L with cushions and Hi-Lo table, Aft Steering wheel, Teak with stainless steel rim Storage boxes under seats with Teak grating Storage locker moulded behind L-settee Windshield New Stainless Steel Propane GrillElectronics and NavigationNew Garmin 48NM Radar (2) Garmin 15" Touchscreen Displays with Chartplotter and Sounder (1 at Upper, 1 at Lower)(2) Hydraulic Assist Steering Systems, Teleflex Capilano (1) at each helm Autopilot, Simrad RPU300 12V/hydraulic pump controls at each helm Trim Tabs, Bennett - toggle control panels at each helm Bow Thruster, Side-Power SP-155-TCI, 20hp/24V joystick panels at each helm Stabilizers, Naiad, 24V, 1250psi, digital MultiSeaII controls at each helm Compass, Ritchie PowerDamp+ (1) at each helm Simrad AP20 Autopilot (1) at each helm ICOM IC-M422 VHF at Flybridge Horizon VHF (1) at each helm Simrad IS15 depth display (1) at each helm Jabsco remote searchlight control (1) at each helm Garmin GND10 Instrument/Display interface switch box Garmin GSD-22 Depth Sounder Processor at Lower Helm FireBoy Xintex FR-1000 CO monitor display at Flybridge Bennett Trim Tab control toggle panel at Flybridge Bow Thruster, Side-Power SP-155-TCI, 24V Glendening Synchronizer Air Conditioning, MarineAir, (5) units Aquadrive anti-vibration system w/matching engine mounts (3) Bilge pumps, 2000 gph Whale manual diaphragm pump Drip pans under engines Engine raw water intake strainers Engine room sound insulation Engine start-stop at Lower Helm Exhaust system, sea-water cooled Fireboy Fire System (5) Fire Extinguishers in Galley, Salon, Master Stateroom, Engine Room & Flybridge Fresh water outlet in engine room Fuel filters, Racor Fuel manifold system Fuel tanks, mild steel, baffled Fuel tanks with upper & lower automatic self-closing valves for sight gauges Panish dual lever controls Propellers, bronze Spare Props Propeller shafts, stainless steel Rudders, fiberglass Seacocks on all thru-hulls below waterline Separating filters, fuel-water Thrust Bearings, Aquadrive Dripless Shaft Seals, Norscot Stabilizers, Naiad Steering, hydraulic Struts, bronze with rubber bearings Throttle and gear shift controls, dual station Trim Tabs, Bennett Central Vacuum System, Beam Water tanks, marine aluminum Water/gas separator installed on generators exhaust system Watermaker, FCI AquaMiser+, 600 gal/day, UpgradeElectrical SystemsNewer (2019) Onan Generator with Sound Shield, 21.5kw, 679 hours New (2021) Onboard Solutions 2000w TruePower Inverter Alternator, each engine Batteries, (4) 8D, Deep Cycle and (1) Group 27 - New Feb 2026 (2) Battery chargers, Professional Mariner 50-amp Battery selector switch (4) Bilge pumps, automatic, 12V and (1) manual - 2 New Feb 2026 Bonding system Cable, tinned-copper Circuit breakers on all circuits Engine room blowers, 12V Engine room lights, 12V Fresh water system, pressurized, 12V Fail Safe Galvanic isolator - NEW Feb 2026 Generator amp and volt meters Generator compartment exhaust blower, 12V Ground fault circuit interrupters Holding tank with pump out, 12V Indicator light, bilge pump Indicator light, reverse polarity Navigation lights, 12V Shore power inlets, 50-amp 220V AC, fwd & aft Spreader lights on mast, 12V Washer and Dryer, Whirlpool Water heater, Seaward 20-gal Updates and Upgrades - Previous and Current Owners Since 2017 01-12-17 Replaced 3 house batteries ($280 each), 2 starter batteries, 2 12-volt thruster batteries ($523 each), generator battery. 01-12-17 Acid flushed 5 AC units ($382) 01-16-17 Complete maintenance on VacuFlush system; New motor on starboard head; New valves, duckbills, etc. 01-19-17 Repaired tachometers (2) 01-23-17 Maintenance/certification on Firebox and 4 CO2 fire extinguishers. 02-03-17 Fix Fusion system on bridge and anchor light switch 03-03-17 Bottom paint/zincs/etc. ($5,703) Coral Bay Marina 03-03-17 Bi-annual maintenance on stabilizers ($1500) Stabilized Mar 03-06-17 Hot water tank hose connection leak repaired ($290 John Hall) 03-15-17 (3219) Replaced the 6 engine zincs 03-17-17 Full detail. compound, wax, teak, metal polishing. ($3600) Jolene. $50 ft x 55, plus for hull and topside bridge area 03-24-17 Fiberglass repairs/selective painting ($1200 Ben Dill) 03-20-17 Watermaker; Installed new membrane.; New low pressure gauge; ($600 SALT?Chris) 03-24-17 Dinghy Annual service ($1700 J&B Marine) 04-06-17 Dinghy Annual; Wiring; Lights; Sump pump; etc. ($1,736 J&B Marine) 04-07-17 Watermaker Membrane; LP Gauge; Filters ($600 SALT) 05-06-17 Spare Cat Seawater pump ($1,111.62 John Hall) 05-06-17 Spare Cat Alternator ($341.41 John Hall) 05-06-17 Replace engine heat exchanger end caps ($60 John Hall) 05-06-17 Fill fuel tanks P=564 S=529 (Engine hours 3219) 05-11-17 Replaced Starboard Water pump as a precaution 05-17-17 Replaced GenSet Seawater pump ($500 J. Hall) 08-02-17 Replaced hot water heater ($1,716 Aquatech) 09-04-17 Teak deck refinishing/Repair ($11,175 Christian Mikkelsen) 11-06-17Replace Watermaker Membrane ?ordered new solenoid ($430 Chris) 11-17-17 Replace G-Wind 12-09-17 Replaced all zincs 12-09-17 Varnished boat 3 coats (Baldy $4200) Last time (01-16-16) 2 coats $3600 12-17-17 Paint wings (4) (Baldy $2300) 2018 01-18-18 Replaced AC controller with new Passport I/O on Mid-Salon Unit ($400 Chris) 01-11-18 Replaced Starter Batteries; AGMs ($1700 J. Hall) 01-11-18 Replaced ProMariner Starter Battery Chargers and 60 AMP Breaker ($800 J. Hall) 01-18-18 Replaced mid salon AC controller ($400) 04-23-18 Replaced Starboard engine impeller (eng: 3300 hrs) Water pump OK. No leaks. Impeller was OK too. (Hall) 04-28-18 Replace controller on mid salon AC (SALT $322) 05-07-18 Fireboy, extinguisher updates; Monroe County Fire Equipment )$338.63 Robert Dillon) 05-06-18 Replaced GenSet fuel pump (Hull) 05-08-18 Replaced Port leaking water pump. (Hall) 05-08-18 Replaced seawater pump assembly ($1,112 Hall) 05-08-18 Replaced generator impeller (Hall) ­­­____hrs. 05-10-18 Full detailing/metal?1 step Vibra, 2-step Awesome Buff, 3 step Vitreo ($3560 Jolene Durstin) 06-05-18 Dinghy annual maintenance (J&B $929) 06-13-18 (3334) Check all belts/replace eng rm light (Hall $1250) 07-10-18 Replace port head bellows (Chuck installed) ($339 Nassau) 08-07-18 Replace AC Water Pump Assembly; Hole in housing (Hall $1,045) Entire pump replaced 9/23/15 for $1,500 by Hall) 08-10-18 Replaced starboard head bellows/bought spare ($1900) Replaced gauges for both heads ($1500) (Key Boatworks Tom) 08-17-18 KVH Antenna fuse. (Seamark Electronics) 09-05-18 Air filter/gaskets/hoses,valve adj. clean/reseal trans coolers; Rebuild oil cooler (stbd) Change transmission oil. Flush engs (Diesel Doc $5,077.47---labor $3875) 09-05-18 New Robertson AP 20 Autopilot for Bridge ($1500 Motion Marine) Installed 10-26-18 Roballo troubleshooting; VHS/Starter battery connections loose; Battery and trim switches replaced (J&B $528) 11-19-18 Fireboy shutdown systems (Seacoast $3,100) 2019 01-02-19 Promatic charger ($626) & other electrical (Hall $2,533) 01-03-19 Salon TV ($500) 01-09-19 Glasstech Bottom Paint, etc. $7,193 Bent prop work $1,200 Underwater lights $2,190 Paint bottom stripe $1,20 Plus misc. electrical work; Total bill $21,070 01-09-19 Stabilizer Maintenance Stabilized Marine ($1,250) 01-10-19 G3 Garmin Vision Map West Marine ($399) 02-01-19 New Salon AC Unit (SALT $605 + $2000+) 2-10-19 Battery isolator, switches, GFI's, etc. (John Hall $1310) 03-05-19 New Onan 21.5 MDKDR Generator (Ted Kaster $25,466.80) 2020 02-01-20 Teak Refurbishing (Christain Mickelson $6,350) 04-06-20 Changed out all zincs. Weren't too bad 06-18-2020 Replaced 3 house batteries (John Hall $1,500) 07-15-20 Bottom paint/speed prop/zincs/grind & fill spots ($6,500). PPS shaft seals ($2,900), replace port cutlass bearing ($2,700), detail to rub rail ($900) -Total bill: $13,055. 11-18-20 Replace compressor in refrig (SALT $2,360) 12-15-20 Re-upholster interior (fabric $3000/labor $5,500) 2021 2023 2025 2026 DisclaimerThe Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.Additional Units Included The listed specifications include 870 hp of total engine power and a maximum draft of 4.83 ft.

Specifications